
Cryogenic mold removal for marina condos, docks and commercial buildings
Dry Ice Blasting Mold MARINA DEL REY CA Without Water Damage
Dry Ice Blasting Mold MARINA DEL REY CA is a waterless remediation method that lifts mold, char and surface grime off wood, brick, concrete and metal using compressed CO2 pellets. We handle condos along Via Marina, harbor-side commercial kitchens and crawl spaces in Los Angeles County. If you found black mold after a slab leak or winter rain intrusion, we can inspect today and blast tomorrow.
What's included
What Our Dry Ice Blasting Mold Service Includes
Every dry ice blasting mold job includes the full scope from inspection through clearance. We do not quote the blast as a standalone line item and leave you to handle containment or testing on your own.
Full Mold Inspection
Moisture meter readings, thermal imaging and boroscope inspection of wall cavities and subfloor. You get photos of every reading and a written scope that names the exact surfaces to be blasted.
Containment And Air Scrubbing
Poly sheeting barriers, negative air machine and HEPA-filtered air scrubbers running for the duration of the job. This keeps spores out of the rest of your home or building while we work.
Dry Ice Blasting Removal
The core service. We blast every contaminated surface with the dry ice blasting machine while a second technician captures debris with a HEPA vacuum at the nozzle. Includes setup, blasting and cleanup of the containment zone.
Antimicrobial Treatment
Application of a mold remediation chemical such as Concrobium or Fiberlock to the blasted surfaces. This kills any remaining spores the blast did not physically remove and gives the surface residual protection.
Encapsulation And Fogging
Encapsulation paint on porous framing that will stay hidden behind walls, plus fogging treatment to reach airborne spores. Both steps are included in the quoted price, not billed as add-ons.
Post-Remediation Verification
Moisture check and, when you want third-party proof, coordination of mold spore testing with an independent lab. You get the clearance report and a written workmanship warranty on the remediation.
Service overview
Dry Ice Blasting Mold MARINA DEL REY CA: How It Works
Dry ice blasting mold in MARINA DEL REY CA uses solid carbon dioxide pellets fired at roughly 300 to 500 feet per second. The pellets hit the mold at -109 degrees Fahrenheit, freeze it, and the sudden temperature change pops the growth off the substrate. Because the dry ice sublimates on contact, there is no secondary blast media to sweep up, no water to dry, and no chemical residue left behind. We pair the blaster with a HEPA vacuum and air scrubber running at the same time so spores never settle back onto clean surfaces.
Most MARINA DEL REY dry ice mold remediation calls start the same way: a slow supply-line drip behind a kitchen cabinet, a failed water heater pan in a Marina City Club unit, or salt air pushing moisture into a ground-floor crawl space. Traditional sanding and wire brushing scratch the wood and push spores into the air. Dry ice mold cleaning MARINA DEL REY California crews use leaves the grain intact, which matters when you are trying to save original 1970s teak paneling or exposed ceiling beams. If you searched for dry ice blasting mold near me MARINA DEL REY, we are typically on site the same day you call.
The service timeline
What Our Dry Ice Blasting Mold Process Looks Like
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection And Moisture Mapping
We walk the unit with a moisture meter and thermal imaging camera to find the wet zone, not just the visible mold. A boroscope confirms growth inside wall cavities and under cabinets. You get photos of every reading. This step takes 45 to 90 minutes on a typical 900-square-foot Marina del Rey condo.
Containment And Air Scrubbing
We hang poly sheeting to seal the work zone and set up a negative air machine with HEPA filters. That keeps spores from drifting into the rest of your home while we work. On commercial jobs along Admiralty Way, we schedule containment around your business hours so you do not lose a full day of revenue.
Dry Ice Blasting
Our technician runs the dry ice blasting machine at 120 to 150 PSI, working top-down and back-to-front. A second tech holds the HEPA vacuum at the blast point to capture debris as it releases. A typical bathroom or kitchen cavity takes two to four hours. Full crawl spaces run six to eight hours and may need a second day.
Antimicrobial And Encapsulation
After blasting, we apply a mold remediation chemical such as Concrobium or Fiberlock ShockWave to the cleaned surface, then seal porous framing with encapsulation paint where it will stay hidden. Fogging treatment reaches the last airborne spores in the room. We let the coating cure per the manufacturer's spec, usually 24 hours.
Post-Remediation Verification
We return with a moisture meter and, when you want third-party proof, coordinate mold spore testing with an independent lab. Clearance air samples confirm the spore count is back to the outdoor baseline. You get the lab report and a written workmanship warranty. Most jobs clear on the first test.
Tools & methods
Tools And Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Dry Ice Blasting Machine
Fires CO2 pellets at 120 to 150 PSI to freeze and lift mold off wood, brick, concrete and metal. The core tool for every job we run.
HEPA Vacuum
Captures mold debris and spores at the blast point before they can settle on clean surfaces. Runs alongside the blaster for the entire removal step.
Air Scrubber And Negative Air Machine
Maintains negative pressure inside containment and filters the air 4 to 6 times per hour. Keeps spores from migrating into the rest of the building.
Thermal Imaging Camera And Moisture Meter
Maps the wet zone behind walls and under floors so we blast the actual source, not just the visible stain. Readings are documented before and after.
Boroscope
Confirms mold growth inside wall cavities and under cabinets through a 4-inch access hole. Tells us whether to blast or cut out the section.
Fogging Machine
Applies fogging solution after blasting to reach airborne spores and tight crevices the nozzle cannot hit directly.
Dehumidifier And Air Movers
Pulls moisture content below 15 percent before blasting. Dry ice on wet wood just spreads the problem, so drying comes first on water damage jobs.
Use cases
When To Call For Dry Ice Blasting Mold
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Mold In Silver Strand Duplex
Groundwater wicking kept the crawl space at 22 percent moisture content, and white and black mold covered roughly 300 square feet of joists and subfloor. The homeowner had a persistent musty odor in the living room above. → We ran a dehumidifier for 24 hours to pull moisture below 15 percent, then blasted the joists, subfloor and foundation walls. Encapsulation paint sealed the wood. Post-job moisture reading was 10 percent, and the odor cleared within a week.
Walk-In Cooler Mold At Fisherman's Village Restaurant
Condensation on the cooler wall panels produced mold across 80 square feet of paneling and framing. The health inspector flagged it during a routine visit, and the restaurant had 10 days to remediate or face a re-inspection. → We contained the cooler, blasted the panels and framing in a single shift between lunch and dinner service, and applied a food-safe mold remediation chemical. The re-inspection passed the following week with no violations. The kitchen never closed.
Problems we solve
Mold Problems We Solve With Dry Ice Blasting
Dry ice blasting mold for commercial property MARINA DEL REY CA and residential jobs solves the problems that standard remediation cannot. Here are the ones we see most often.
Black mold behind cabinets and drywall
We cut a small access hole, confirm the growth with a boroscope, and blast the framing through the opening. The dry ice freezes the mold off the wood without scratching it, and the HEPA vacuum captures the debris at the source. The wall closes back up the same day.
Crawl space mold from groundwater wicking
We run a dehumidifier first to pull moisture content below 15 percent, then blast the joists, subfloor and foundation walls with dry ice. The nozzle fits between 16-inch joist spacing. After blasting, we apply encapsulation paint to seal the wood.
Musty odor that returns after cleaning
We track the odor to its source with thermal imaging and boroscope inspection, blast the hidden growth, then run fogging treatment to knock down airborne spores. Odor removal mold jobs usually clear in one visit with a follow-up moisture check at 30 days.
Mold on commercial kitchen equipment and walls
We schedule dry ice blasting around your operating hours, contain the work zone, and blast the walls, hood surrounds and cooler panels in a single shift. No chemical residue means you can reopen the kitchen as soon as containment comes down.
Pricing process
Dry Ice Blasting Mold Pricing In Marina del Rey
$1,200 - $12,000 depending on scope
Square footage affected
A single bathroom cavity runs $1,200 to $2,000. A full crawl space or commercial kitchen runs $5,000 and up. We measure the actual contaminated area during inspection, not the whole room.
Access and containment complexity
Third-floor condos with limited staging, shared walls and HOA notice requirements add labor. Ground-floor units with direct access are faster and cheaper to contain.
Depth of mold growth
Surface mold blasts off in one pass. Mold that has penetrated into the wood grain or behind multiple layers of drywall takes longer and may require cutting out a section.
How much does dry ice blasting mold cost in MARINA DEL REY CA?
Most residential dry ice blasting mold jobs in Marina del Rey run $1,800 to $4,500 in 2026. A single bathroom cavity or kitchen cabinet starts around $1,200. Full crawl spaces and commercial kitchens run $5,000 to $12,000 depending on square footage and access. The price includes containment, blasting, antimicrobial treatment and a post-remediation moisture check. Third-party lab testing is billed separately at $150 to $350 per sample set.
Is dry ice blasting safe for mold removal in MARINA DEL REY California?
Yes. Dry ice blasting is safe for wood, brick, concrete, metal and most plastics when the technician controls pressure and distance. The CO2 pellets sublimate into gas, so there is no abrasive media to breathe and no chemical residue. We still run a HEPA vacuum and air scrubber at the blast point because mold spores are the hazard, not the dry ice. Occupants stay out of the containment zone until clearance testing passes.
How does dry ice blasting remove mold in MARINA DEL REY CA?
The blaster fires dry ice pellets at -109 degrees Fahrenheit and 120 to 150 PSI. The pellets freeze the mold on contact, and the thermal shock plus kinetic energy lifts it off the surface. Because the pellets turn straight to gas, the mold flakes off dry and gets captured by the HEPA vacuum running beside the nozzle. A 100-square-foot wall section takes 45 to 90 minutes to blast clean.
Who does dry ice mold remediation in MARINA DEL REY?
Mold Remediation Service Marina Del Rey handles dry ice mold remediation for condos, single-family homes and commercial buildings across the 90292 ZIP code. We cover Marina del Rey, Silver Strand, Marina Peninsula, Fisherman's Village and the surrounding Los Angeles County areas. Call (833) 929-5837 for a same-day inspection. We are licensed, insured and have been blasting mold since 2024.
Ready when you are
Get Dry Ice Blasting Mold MARINA DEL REY CA Scheduled Today
We are licensed, insured and have been blasting mold in Marina del Rey since 2024. Call (833) 929-5837 and we will inspect the same day, quote a fixed price, and schedule the blast before the mold spreads further.

Talk with the local team
Request Dry Ice Blasting Mold
Call (833) 929-5837 any time, day or night. A live person answers, and for active leaks or visible mold we can usually get a crew to your property the same day. If you prefer email, send photos and a short description to info@moldremediationservicemarinadelrey.com and we will follow up with next steps.



